Finally just seemed to work in normal mode (no admin, no compat mode).įingers crossed it still works when i boot up again. Took about 20 attempts and running a maintenance task in every way. Ran in compatibility mode, then not, then it seemed to work. So, i uninstalled, re installed, ran as admin, then as not. That latest windows 10 update completely ruining my PC. Steinberg Support Software/license activation & reactivation This article refers to eLicenser-based license management.If your software uses Steinberg Licensing introduced in January 2022,the following information is not relevant for you. Follow the instructions for Reactivation. If I do not open the licenser center first, and just open Cubase 9.5 like I used to by clicking on the icon etc. Before installing any of the Cubase 11 components below the following utilities must be installed resp. Install your CB LE10 software on your new computer. But the only way to get everything to work without any error messages, is to run as admin my licenser center first, it then opens, then open cubase 9.5 as admin, and then everything opens and runs. I updated the licenser, uninstalled and reinstalled everything, updated Cubase and switched USB ports for the dongle. I get that error message now about permissions. But the last week after windows 10 updates. My Cubase 9.5 was running fine since I got it the day it came out. Should there be any? Cubase seems to think so… When I launch the eLicenser Control Center, I see all of my licenses in the “USB-eLicenser” panel, but there are no licenses in the “Soft-eLicenser ( SeL)” panel. Incidentally, I have no idea what the “Soft-eLicenser ( SeL)” is, as there was no such thing when I started using this dongle. I’ve also had these problems with the current and previous versions of the RME driver. I’ve had this problem with eLC software v6., and then with v6. Then, as I try to close Windows, RME driver hdsp64.sys crashes and causes a “PROCESS_HAS_LOCKED_PAGES” Blue Screen. If I click “OK,” the programs continue to load… but then, when I try to assign a MIDI port in a MIDI track in Cubase (one of RME’s special low-latency GSIF MIDI ports) Giga crashes. Soft-elicenser doesn’t have enought permissions to run properly. (2) launch Cubase after I’ve launched GigaStudio, Visit the login page and click on 'Forgot your password'. I would like to change the password for my reFX customer account. If you still can't find your download / product, please submit a ticket and our staff will help. Just installed a new RME RayDAT sound card (main card is Rev.1.2, daughter card is Rev.1.1). Simply visit your 'downloads' page to gain access to the app. Running Cubase 5.5.2 (64-bit)… which worked fine until today. Where it is needed, the USB-eLicenser must be purchased separately, unless you already own one. Same (Syncrosoft) dongle I’ve been using for years. The USB-eLicenser is a copy protection device which is required by certain Steinberg products, including versions of Cubase, Nuendo and WaveLab released before 2022. Once this is done, download directly from the official product page and proceed to install it on your equipment, remember to have your equipmentĭuly updated, many times the lack of updating of the equipment can provide download errors in this case.New PC, running Windows 7 (64-bit). In this case, uncheck or delete the download of your equipment, verify that it is not or is not in the download history. In case the installation fails, try to run the installation again after disconnecting the USB-eLicenser. Therefore, if a USB-eLicenser or a specific license is not recognized or error messages related to the license appear when you start your Steinberg software, the first thing you should do is download and install the latest version of the eLicenser Control Center. The USB-eLicenser can be directly connected to a computer.The USB-eLicenser can be connected to a computer via a USB port. Most of the most common problems related to the USB-eLicenser (dongle, officially called Steinberg Key), Soft-eLicenser and/or the license are due to an outdated or damaged installation of the eLicenser Control Center. My name is Anthony, an Independent Advisor trying to help.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |